Strange error when I run CD-ROM or ISO

VanHalenMan · July 26th, 2007

Ok, I have ePSXe up and running on a good cpu but I can not run a CD-ROM for some reason with this computer so I made an Iso of the game I want to play (FFVII) and the disk is in just bad enough condition that the iso is screwed up and when I get to a point in the game where it just stops working because of the iso. So I try to run ePSXe on a different computer and the cdrom pluggin can seem to recognize the drive but when I run it this strange error comes up:

Code:

The instruction at "0x00e450c" referenced memory at "0x00000000". The memory could not be "Read".

I used every cd-rom pluggin that I could find including Xevens and several of Petes. The same error comes up when I try to run the iso. Does it have anything to do with the fact that the computer has Win 2k? of the 3 computers that I have tried it with, only 1 of them has worked. Thank you for your time.

RedLion · July 26th, 2007

Hello VanHalenMan and welcome to Emuforums.
Have you tried to make the iso with isobuster?

VanHalenMan · July 27th, 2007

Well, I DO havd Isobuster and I have tried it in the past and if I remember correctly it didn't work, but that was on a different computer so I will try it.

Ok, I tried it with Iso Buster, and I think I had it place 0s in any section that is to scratched to read, and it didn't work, unless I should have had it do something else when it can't read a section. What should I do?

July 26th, 2007	#1 (permalink)
VanHalenMan Registered User Join Date: Jul 2007 Location: North Canton Ohio Posts: 39	Strange error when I run CD-ROM or ISO Ok, I have ePSXe up and running on a good cpu but I can not run a CD-ROM for some reason with this computer so I made an Iso of the game I want to play (FFVII) and the disk is in just bad enough condition that the iso is screwed up and when I get to a point in the game where it just stops working because of the iso. So I try to run ePSXe on a different computer and the cdrom pluggin can seem to recognize the drive but when I run it this strange error comes up: Code: The instruction at "0x00e450c" referenced memory at "0x00000000". The memory could not be "Read". I used every cd-rom pluggin that I could find including Xevens and several of Petes. The same error comes up when I try to run the iso. Does it have anything to do with the fact that the computer has Win 2k? of the 3 computers that I have tried it with, only 1 of them has worked. Thank you for your time.

July 27th, 2007	#3 (permalink)
VanHalenMan Registered User Join Date: Jul 2007 Location: North Canton Ohio Posts: 39	Well, I DO havd Isobuster and I have tried it in the past and if I remember correctly it didn't work, but that was on a different computer so I will try it. Ok, I tried it with Iso Buster, and I think I had it place 0s in any section that is to scratched to read, and it didn't work, unless I should have had it do something else when it can't read a section. What should I do? Last edited by VanHalenMan; July 27th, 2007 at 17:57. Reason: Automerged Doublepost

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

July 26th, 2007	#2 (permalink)
RedLion Powerful sighting Join Date: Jul 2006 Location: Urban Jungle Posts: 1,753	Hello VanHalenMan and welcome to Emuforums. Have you tried to make the iso with isobuster?